diff --git a/keyboards/atom47/atom47.c b/keyboards/atom47/atom47.c new file mode 100644 index 000000000..7b839e796 --- /dev/null +++ b/keyboards/atom47/atom47.c @@ -0,0 +1,31 @@ +#include "atom47.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); +}; + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + matrix_scan_user(); +}; + +void led_init_ports(void) { + // * Set our LED pins as output + DDRB &= ~(1<<5); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0003 +#define MANUFACTURER Vortex +#define PRODUCT Core +#define DESCRIPTION Atom47 PCB for the Vortex Core + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 13 + +// ROWS: Top to bottom, COLS: Left to right + +#define MATRIX_ROW_PINS {B1,B2,B3,B7} +#define MATRIX_COL_PINS {D7,D5,F0,F1,F4,F6,F7,D4,C7,C6,D6,B5,B4} +#define UNUSED_PINS + +#define BACKLIGHT_PIN B6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* Backlight configuration + */ +#define BACKLIGHT_LEVELS 4 + +#endif + +#define RGB_DI_PIN D0 // The pin the LED strip is connected to +#define RGBLED_NUM 1 // Number of LEDs in your strip + +#define QMK_ESC_OUTPUT D7 // usually COL +#define QMK_ESC_INPUT B1 // usually ROW +#define QMK_LED B6 \ No newline at end of file diff --git a/keyboards/atom47/keymaps/LEdiodes/atom47.c b/keyboards/atom47/keymaps/LEdiodes/atom47.c new file mode 100644 index 000000000..7b839e796 --- /dev/null +++ b/keyboards/atom47/keymaps/LEdiodes/atom47.c @@ -0,0 +1,31 @@ +#include "atom47.h" +#include "led.h" + +void matrix_init_kb(void) { + // put your keyboard start-up code here + // runs once when the firmware starts up + matrix_init_user(); + led_init_ports(); +}; + +void matrix_scan_kb(void) { + // put your looping keyboard code here + // runs every cycle (a lot) + matrix_scan_user(); +}; + +void led_init_ports(void) { + // * Set our LED pins as output + DDRB &= ~(1<<5); +} + +void led_set_kb(uint8_t usb_led) { + if (usb_led & (1<. +*/ + +#ifndef CONFIG_H +#define CONFIG_H + +#include "config_common.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x6060 +#define DEVICE_VER 0x0003 +#define MANUFACTURER Vortex +#define PRODUCT Core +#define DESCRIPTION Atom47 PCB for the Vortex Core + +/* key matrix size */ +#define MATRIX_ROWS 4 +#define MATRIX_COLS 13 + +// ROWS: Top to bottom, COLS: Left to right + +#define MATRIX_ROW_PINS {B1,B2,B3,B7} +#define MATRIX_COL_PINS {D7,D5,F0,F1,F4,F6,F7,D4,C7,C6,D6,B5,B4} +#define UNUSED_PINS + +#define BACKLIGHT_PIN B6 + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* define if matrix has ghost */ +//#define MATRIX_HAS_GHOST + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* Backlight configuration + */ +#define BACKLIGHT_LEVELS 4 + +#endif + +#define RGB_DI_PIN D0 // The pin the LED strip is connected to +#define RGBLED_NUM 1 // Number of LEDs in your strip + +#define QMK_ESC_OUTPUT D7 // usually COL +#define QMK_ESC_INPUT B1 // usually ROW +#define QMK_LED B6 \ No newline at end of file diff --git a/keyboards/atom47/keymaps/LEdiodes/keymap.c b/keyboards/atom47/keymaps/LEdiodes/keymap.c new file mode 100644 index 000000000..3ea8609b6 --- /dev/null +++ b/keyboards/atom47/keymaps/LEdiodes/keymap.c @@ -0,0 +1,35 @@ +#include QMK_KEYBOARD_H + +// These are all aliases for the function layers. +#define _L0 0 +#define _L1 1 +#define _L2 2 +#define _L3 3 + +#define _______ KC_TRNS + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[_L0] = KEYMAP_ANSI( + KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \ + KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_L1), \ + KC_LCTL, KC_LGUI, KC_LALT, TG(_L3), KC_SPC, KC_SPC, MO(_L2), KC_RALT, KC_APP, KC_RCTRL), \ + +[_L2] = KEYMAP_ANSI( + _______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \ + KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \ + _______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ + +[_L1] = KEYMAP_ANSI( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \ + KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \ + _______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ + +[_L3] = KEYMAP_ANSI( + _______, _______, _______, KC_7, KC_8, KC_9, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, KC_4, KC_5, KC_6, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, KC_1, KC_2, KC_3, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, KC_0, KC_DOT, _______, _______, _______, RESET), \ +}; diff --git a/keyboards/atom47/keymaps/LEdiodes/rules.mk b/keyboards/atom47/keymaps/LEdiodes/rules.mk new file mode 100644 index 000000000..d446d3a69 --- /dev/null +++ b/keyboards/atom47/keymaps/LEdiodes/rules.mk @@ -0,0 +1,65 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/atom47/keymaps/default/keymap.c b/keyboards/atom47/keymaps/default/keymap.c new file mode 100644 index 000000000..cd8e622f2 --- /dev/null +++ b/keyboards/atom47/keymaps/default/keymap.c @@ -0,0 +1,39 @@ +#include QMK_KEYBOARD_H + +// Each layer gets a name for readability, which is then used in the keymap matrix below. +// The underscores don't mean anything - you can have a layer called STUFF or any other name. +// Layer names don't all need to be of the same length, obviously, and you can also skip them +// entirely and just use numbers. + +#define _MA 0 //Main layer +#define _FN 1 //Fn +#define _FN1 2 //Fn1 +#define _PN 3 //Pn + +#define _______ KC_TRNS + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +[_MA] = KEYMAP_ANSI( + KC_ESC, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_DEL, KC_BSPC, \ + KC_TAB, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_ENT, \ + KC_LSFT, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_RSFT, MO(_FN1), \ + KC_LCTL, KC_LGUI, KC_LALT, MO(_PN), KC_SPC, KC_SPC, MO(_FN), KC_RALT, KC_APP, KC_RCTRL), \ + +[_FN] = KEYMAP_ANSI( + _______, KC_VOLD, KC_VOLU, KC_MUTE, RESET, _______, KC_CALC, KC_PGUP, KC_UP, KC_PGDN, KC_PSCR, KC_SLCK, KC_PAUS, \ + KC_CAPS, KC_MPRV, KC_MPLY, KC_MNXT, _______, _______, KC_HOME, KC_LEFT, KC_DOWN, KC_RIGHT, KC_INS, _______, \ + _______, _______, _______, _______, _______, _______, _______, BL_TOGG, BL_DEC, BL_INC, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ + +[_FN1] = KEYMAP_ANSI( + KC_GRV, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, \ + KC_1, KC_2, KC_3, KC_4, KC_5, KC_6, KC_7, KC_8, KC_9, KC_0, KC_MINS, KC_EQL, \ + _______, _______, _______, _______, _______, KC_QUOT, KC_SLSH, KC_LBRC, KC_RBRC, KC_BSLS, KC_RSFT, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______), \ + +[_PN] = KEYMAP_ANSI( + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET), +}; \ No newline at end of file diff --git a/keyboards/atom47/keymaps/default/readme.md b/keyboards/atom47/keymaps/default/readme.md new file mode 100644 index 000000000..02422eb97 --- /dev/null +++ b/keyboards/atom47/keymaps/default/readme.md @@ -0,0 +1,10 @@ +To be updated... + + +// This layer is just a blank template to be copied for easy layer creation. please don not edit it. + + [_LX] = KEYMAP_ANSI( + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, _______, \ + _______, _______, _______, _______, _______, _______, _______, _______, _______, RESET), diff --git a/keyboards/atom47/readme.md b/keyboards/atom47/readme.md new file mode 100644 index 000000000..fec7843ae --- /dev/null +++ b/keyboards/atom47/readme.md @@ -0,0 +1,28 @@ +# ATOM47 + +![ATOM47](https://i.imgur.com/rjrFTKT.png) + +## Support +Keyboard Maintainer: [Matthew Kerfoot(https://github.com/mkerfoot) +Hardware Supported: ATOM47 +Hardware Availability: [GeekHack.com Group Buy](https://geekhack.org/index.php?topic=93447.msg2545221) + + +## Features +QMK Firmware +6 Underglow RGB leds +In-switch leds +Through-hole micro usb connector (less likely to break off!) +South facing leds for the QMX/Zealencio users +Multiple layouts +Easily reachable reset button under the spacebar +CapsLock indicator + +## Build +To build the default keymap, simply run `make atom47:default`. + +For an alternative, heavily modified layout you would just need to run `make atom47:LEdiodes`. + +See [build environment setup](https://docs.qmk.fm/build_environment_setup.html) then the [make instructions](https://docs.qmk.fm/make_instructions.html) for more information. + +![ATOM47](https://i.imgur.com/WebeUOF.png) diff --git a/keyboards/atom47/rules.mk b/keyboards/atom47/rules.mk new file mode 100644 index 000000000..d446d3a69 --- /dev/null +++ b/keyboards/atom47/rules.mk @@ -0,0 +1,65 @@ +# MCU name +#MCU = at90usb1287 +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +# Teensy halfKay 512 +# Teensy++ halfKay 1024 +# Atmel DFU loader 4096 +# LUFA bootloader 4096 +# USBaspLoader 2048 +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = no # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = no # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +RGBLIGHT_ENABLE = no # Enable keyboard underlight functionality (+4870) +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality (+1150) +MIDI_ENABLE = no # MIDI controls +AUDIO_ENABLE = no +UNICODE_ENABLE = no # Unicode +BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID diff --git a/keyboards/dz60/keymaps/LEdiodes/config.h b/keyboards/dz60/keymaps/LEdiodes/config.h new file mode 100644 index 000000000..bb78d9bb6 --- /dev/null +++ b/keyboards/dz60/keymaps/LEdiodes/config.h @@ -0,0 +1,58 @@ +#ifndef CONFIG_H +#define CONFIG_H + +#include "config.h" + +/* USB Device descriptor parameter */ +#define VENDOR_ID 0xFEED +#define PRODUCT_ID 0x2260 +#define DEVICE_VER 0x0001 +#define MANUFACTURER KBDFans +#define PRODUCT DZ60 +#define DESCRIPTION DZ60 Keyboard + +/* key matrix size */ +#define MATRIX_ROWS 5 +#define MATRIX_COLS 15 + +/* key matrix pins */ +#define MATRIX_ROW_PINS { D0, D1, D2, D3, D5 } +#define MATRIX_COL_PINS { F0, F1, E6, C7, C6, B7, D4, B1, B0, B5, B4, D7, D6, B3, F4 } +#define UNUSED_PINS + +/* COL2ROW or ROW2COL */ +#define DIODE_DIRECTION COL2ROW + +/* number of backlight levels */ +#define BACKLIGHT_PIN B6 +#define BACKLIGHT_LEVELS 5 + +/* Set 0 if debouncing isn't needed */ +#define DEBOUNCING_DELAY 5 + +/* Mechanical locking support. Use KC_LCAP, KC_LNUM or KC_LSCR instead in keymap */ +#define LOCKING_SUPPORT_ENABLE + +/* Locking resynchronize hack */ +#define LOCKING_RESYNC_ENABLE + +/* key combination for command */ +#define IS_COMMAND() ( \ + keyboard_report->mods == (MOD_BIT(KC_LSHIFT) | MOD_BIT(KC_RSHIFT)) \ +) + +/* prevent stuck modifiers */ +#define PREVENT_STUCK_MODIFIERS + +#define RGB_DI_PIN E2 +#define RGBLIGHT_ANIMATIONS +#define RGBLED_NUM 16 +#define RGBLIGHT_HUE_STEP 8 +#define RGBLIGHT_SAT_STEP 8 +#define RGBLIGHT_VAL_STEP 8 + +/* sets 'Auto Shift' timeouts */ +#define AUTO_SHIFT_TIMEOUT 150 +#define NO_AUTO_SHIFT_SPECIAL + +#endif diff --git a/keyboards/dz60/keymaps/LEdiodes/keymap.c b/keyboards/dz60/keymaps/LEdiodes/keymap.c new file mode 100644 index 000000000..46bdb5fed --- /dev/null +++ b/keyboards/dz60/keymaps/LEdiodes/keymap.c @@ -0,0 +1,141 @@ +#include "xd60.h" +#include "action_layer.h" + +#Define _L0 0 +#Define _L1 1 +#Define _L2 2 +#Define _L3 3 +#Define _L4 4 + +#define _______ KC_TRNS + +/* + * template + * [_L1] = KEYMAP( + * _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, \ + * _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, \ + * _______, _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, \ + * _______, _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, \ + * _______,_______,_______, _______,_______,_______, _______,_______,_______,_______,_______, + * + * + *\ + +const uint16_t PROGMEM keymaps[][MATRIX_ROWS][MATRIX_COLS] = { +/* Keymap _L0: (Layer 0 - Base Layer) This is the default layer + * This layer has a key set to MO(_L1) which means when held down Layer 1 will become active, If Layer 1 does not have anything set for tat key is will revert to uing the key set at layer 0. + * LT(_L1, KC_1) means that when the "1" key is long touched then it will activate the layer _L1 key(F1) but if the key is just tapped it will activate the "1" key. + * KC_GESC = Escape when tapped, ` when pressed with Shift or GUI + * KC_LSPO = Left Shift when held, ( when tapped + * TD(LT(_L3,KC_SPACE)) = This is a test... hoping it will tap dance if double tapped it does enter if single tap it does space if long hold down it does _L3(Layer 3). + * LT(_L3,KC_SPACE) = if tapped it does space, is long touch it does _L3(Layer 3) + * BL_TOGG = Toggles the LEDs. + * ,-----------------------------------------------------------------------------------------. + * | Esc | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 | 0 | - | = |Bkspc| Del | + * |-----------------------------------------------------------------------------------------+ + * | Tab | Q | W | E | R | T | Y | U | I | O | P | [ | ] | \ | + * |-----------------------------------------------------------------------------------------+ + * | _L4 | A | S | D | F | G | H | J | K | L | ; | ' | Enter | + * |-----------------------------------------------------------------------------------------+ + * | Shift | Z | X | C | V | B | N | M | , | . | / | RSh | U | _L1 | + * |-----------------------------------------------------------------------------------------+ + * | Ctrl | Win | Alt | _L3[Space] |LEdiodes| Space |Win | _L2| L | D | R | + * `-----------------------------------------------------------------------------------------' + */ +[_L0] = KEYMAP( + KC_GESC, LT(_L1, KC_1),LT(_L1, KC_2),LT(_L1, KC_3),LT(_L1, KC_4),LT(_L1, KC_5),LT(_L1, KC_6),LT(_L1, KC_7),LT(_L1, KC_8),LT(_L1, KC_9),LT(_L1, KC_0),LT(_L1, KC_MINS),LT(_L1, KC_EQL),KC_BSPC, KC_DEL, \ + KC_TAB, KC_Q, KC_W, KC_E, KC_R, KC_T, KC_Y, KC_U, KC_I, KC_O, KC_P, KC_LBRC, KC_RBRC, KC_BSLS, \ + KC_CAPS, KC_A, KC_S, KC_D, KC_F, KC_G, KC_H, KC_J, KC_K, KC_L, KC_SCLN, KC_QUOT, KC_NO, KC_ENT, \ + KC_LSPO, KC_NO, KC_Z, KC_X, KC_C, KC_V, KC_B, KC_N, KC_M, KC_COMM, KC_DOT, KC_SLSH, KC_RSPO, KC_UP, M0(_L1), \ + KC_LCTL, KC_LGUI, KC_LALT, TD(LT(_L3,KC_SPACE)),BL_TOGG,TD(TD_SPC_ENT), KC_RGUI, M0(_L2), KC_LEFT, KC_DOWN, KC_RIGHT), + +/* Keymap _L1: (Layer 1) This is function layer 1 + * This layer is activated while the Fn key is being held down. + * ,-----------------------------------------------------------------------------------------. + * | Reset | F1 | F2 | F3 | F4 | F5 | F6 | F7 | F8 | F9 | F10 | F11 | F12 | F13| F14| + * |-----------------------------------------------------------------------------------------+ + * | | WhUp| U | WhDn | | | | | | PrtScr | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | L | D | R | | | Home | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | End | VolDn|VolUp|Mute | | | PgUp| | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | Home| PgDn| End | + * `-----------------------------------------------------------------------------------------' + */ +[_L1] = KEYMAP( + RESET, KC_F1, KC_F2, KC_F3, KC_F4, KC_F5, KC_F6, KC_F7, KC_F8, KC_F9, KC_F10, KC_F11, KC_F12, KC_F13, KC_F14, \ + _______, KC_WH_U, KC_UP, KC_WH_D, _______, _______,_______, _______, _______, _______, KC_PSCR, _______, _______, _______, \ + _______, KC_LEFT, KC_DOWN, KC_RIGHT, _______, _______, KC_HOME, _______, _______, _______, KC_HOME, _______, _______, _______, \ + _______, _______, _______, KC_APP, BL_STEP,_______, KC_END, KC_VOLD, KC_VOLU, KC_MUTE, _______, _______, _______, KC_PGUP, _______, \ + _______, _______, _______, _______,_______,_______, _______, _______, KC_HOME, KC_PGDOWN, KC_END), + +/* Keymap _L2: (Layer 2) This is function layer 2 + * This layer is activated while the Fn2 key is being held down. + * LCA(KC_TAB) = Hold Left Control and Alt and press kc_tab which cycles trough open apps. + * MEH(KC_TAB) = Hold Left Control, Shift and Alt and press kc_TAB to cycle backwards through apps. + * ,-----------------------------------------------------------------------------------------. + * | | | | | | | | | | | | | | | LCA(KC_TAB)| + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | | | | | | |MEH(KC_TAB) + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | || | | | | | + * |-----------------------------------------------------------------------------------------+ + * | | | | | | | | | | | | + * `-----------------------------------------------------------------------------------------' + */ +[_L2] = KEYMAP( + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,LCA(KC_TAB), \ + _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, MEH(KC_TAB), \ + _______, _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______, _______, \ + _______, _______,_______,_______,_______,_______,_______,_______,_______,_______,_______,_______,KC_MS_BTN1,KC_MS_UP,KC_MS_BTN2, \ + _______,_______,_______, _______,_______,_______, _______,_______,KC_MS_LEFT,KC_MS_DOWN,KC_MS_RIGHT, + +}; + +// Custom Actions +const uint16_t PROGMEM fn_actions[] = { + [0] = ACTION_LAYER_MOMENTARY(1), // to Fn overlay +}; + +// Macros +const macro_t *action_get_macro(keyrecord_t *record, uint8_t id, uint8_t opt) { + + // MACRODOWN only works in this function + switch(id) { + case 0: + if (record->event.pressed) { register_code(KC_RSFT); } + else { unregister_code(KC_RSFT); } + break; + } + + return MACRO_NONE; +}; + +// Loop +void matrix_scan_user(void) { + // Empty +}; + +//Tap Dance Declarations +enum { + TD_SPC_ENT = 0, + TD_KC_LSFT_CAPS = 0, + TD_KC_RSFT_CAPS = 0 +}; + +//Tap Dance Definitions +qk_tap_dance_action_t tap_dance_actions[] = { + + //Tap once for space, tap twice for enter + [TD_SPC_ENT] = ACTION_TAP_DANCE_DOUBLE(KC_SPC, KC_ENT), + //Tap once for Left Shift, twice for Caps Lock + [TD_KC_LSFT_CAPS] = ACTION_TAP_DANCE_DOUBLE(KC_LSFT, KC_CAPS), + //Tap once for Right Shift, twice for Caps Lock + [TD_KC_RSFT_CAPS] = ACTION_TAP_DANCE_DOUBLE(KC_RSFT, KC_CAPS) + +// Other declarations would go here, separated by commas, if you have them + +}; diff --git a/keyboards/dz60/keymaps/LEdiodes/readme.md b/keyboards/dz60/keymaps/LEdiodes/readme.md new file mode 100644 index 000000000..db83b2494 --- /dev/null +++ b/keyboards/dz60/keymaps/LEdiodes/readme.md @@ -0,0 +1,9 @@ +# LEdiodes Keymap for XD60 60% PCB + +![LEdiodes Layer 0 Keymap for XD60](https://i.imgur.com/pDneawX.jpg) + +## Additional Notes +Layer 0(default) Keymap for LEdiodes XD60. + +## Build +To build the default keymap, simply run `make xd60:LEdiodes`. diff --git a/keyboards/dz60/keymaps/LEdiodes/rules.mk b/keyboards/dz60/keymaps/LEdiodes/rules.mk new file mode 100644 index 000000000..f54d9500f --- /dev/null +++ b/keyboards/dz60/keymaps/LEdiodes/rules.mk @@ -0,0 +1,57 @@ +# MCU name +MCU = atmega32u4 + +# Processor frequency. +# This will define a symbol, F_CPU, in all source code files equal to the +# processor frequency in Hz. You can then use this symbol in your source code to +# calculate timings. Do NOT tack on a 'UL' at the end, this will be done +# automatically to create a 32-bit value in your source code. +# +# This will be an integer division of F_USB below, as it is sourced by +# F_USB after it has run through any CPU prescalers. Note that this value +# does not *change* the processor frequency - it should merely be updated to +# reflect the processor speed set externally so that the code can use accurate +# software delays. +F_CPU = 16000000 + +# +# LUFA specific +# +# Target architecture (see library "Board Types" documentation). +ARCH = AVR8 + +# Input clock frequency. +# This will define a symbol, F_USB, in all source code files equal to the +# input clock frequency (before any prescaling is performed) in Hz. This value may +# differ from F_CPU if prescaling is used on the latter, and is required as the +# raw input clock is fed directly to the PLL sections of the AVR for high speed +# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL' +# at the end, this will be done automatically to create a 32-bit value in your +# source code. +# +# If no clock division is performed on the input clock inside the AVR (via the +# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU. +F_USB = $(F_CPU) + +# Interrupt driven control endpoint task(+60) +OPT_DEFS += -DINTERRUPT_CONTROL_ENDPOINT + + +# Boot Section Size in *bytes* +OPT_DEFS += -DBOOTLOADER_SIZE=4096 + + +# Build Options +# comment out to disable the options. +# +BOOTMAGIC_ENABLE = yes # Virtual DIP switch configuration(+1000) +MOUSEKEY_ENABLE = yes # Mouse keys(+4700) +EXTRAKEY_ENABLE = yes # Audio control and System control(+450) +CONSOLE_ENABLE = no # Console for debug(+400) +COMMAND_ENABLE = no # Commands for debug and configuration +SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend +NKRO_ENABLE = yes # USB Nkey Rollover - if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work +BACKLIGHT_ENABLE = yes # Enable keyboard backlight functionality +AUDIO_ENABLE = no +RGBLIGHT_ENABLE = yes +AUTO_SHIFT_ENABLE = yes # If the time depressed is greater than or equal to the AUTO_SHIFT_TIMEOUT, then a shifted version of the key is emitted. If the time is less than the AUTO_SHIFT_TIMEOUT time, then the normal state is emitted \ No newline at end of file