With these changes, the ergodox ez goes from 315 scans per second
when no keys are pressed (~3.17ms/scan) to 447 (~2.24ms/scan).
The changes to the pin read are just condensing the logic, and
replacing a lot of conditional operations with a single bitwise
inversion.
The change to row scanning is more significant, and merits
explanation. In general, you can only scan one row of a keyboard
at a time, because if you scan two rows, you no longer know
which row is pulling a given column down. But in the Ergodox
design, this isn't the case; the left hand is controlled by an
I2C-based GPIO expander, and the columns and rows are *completely
separate* electrically from the columns and rows on the right-hand
side.
So simply reading rows in parallel offers two significant
improvements. One is that we no longer need the 30us delay after
each right-hand row, because we're spending more than 30us
communicating with the left hand over i2c. Another is that we're
no longer wastefully sending i2c messages to the left hand
to unselect rows when no rows had actually been selected in the
first place. These delays were, between them, coming out to
nearly 30% of the time spent in each scan.
Signed-off-by: seebs <seebs@seebs.net>
This is particularly relevant for, e.g., the ergodox EZ and
other keyboards with slow scan rates. Without changing the API or
behavior of individual process_record() calls, we allow a
configuration flag to make multiple calls in a single scan.
This will probably have miniscule effects on non-steno users,
and it's not enabled by default for any keyboards. Added note
about it to ergodox README.
Signed-off-by: seebs <seebs@seebs.net>
* move underglow led count from parent to child
* Added pearl support
* Added personal keymap for pearl
* start splitting up ps2avrGB boards
* clean up ps2avrgb boards
* Move keycodes to their own section
* Clarify `KC_PWR` vs `KC_POWER`. Fixes#1994.
* Cleaned uppersonal userspace and keymaps (#1998)
* Cleanup of keymaps
* Remove Tap Dance from Orthodox keymap
* Cleaned up userspace and keymaps
* Added sample (template)userspace files to my folder
* Document the Teensy hardware reset problem
* add mfluid keymap to atreus62
* Update hand_wire.md
Change "Resin" to "Rosin"
* Add keyboard: mt40 (#2001)
* add keyboard: chinese planck clone
* rename chinese_planck to mt40
* add image for the mt40 board
* lets_split: Fix matrix_init for ROW2COL
Signed-off-by: Marian Rusu <rusumarian91@gmail.com>
* Add Keymap for Whitefox Truefox layout
* Add keyboard: ACR60 (#1999)
* base acr60 keyboard folder created
* mitch acr60 keymap updates, documentation
* latest keymap updates
* slight modifications to layer switching
* Changes to Atreus and Ergodox EZ Dvorak 42key layout (#1997)
* importing 42 key dvorak layout
* added comment for build instructions
* adding atreus dvorak 42 key layout
* added readme
* add readme
* build instructions
* additional MEH shortcuts
* added shifted symbols on symbols layer
* working extra symbols on COMBINED layer
* bring atreus layout inline with the ergodox one
* add necessary macros
* working ls macro
* added more shell macros
* added screen rename / screen number macros
* add ctrl-a key in shell-nav to use screen more easily
* added shell screen layer
* assign screen switching macros to screen layer
* define all screen switching macros
* more screen-related shortcuts added on shell screen layer
* change shell nav bottom right row to match base layer (backspace / delete)
* remove some mappings on SHELL_NAV layer as they are now in the screen layer
* added more screen macros
* changes to COMBINED layer (pipe on the right) and modified shell nav
* moved pipe/backslash to then right
* documented SHELL_SCREEN layer
* put backspace/delete on SHELL_NAV layer
* add an explicit lisence file for github to pickup
* Updated keymaps to allow base layer alternation for QWERTY, Colemak & Dvorak (#1962)
* First commit of the Terminus_Mini firmware and the DivergeJM version of the Nyquist firmware
* Fix terminus_mini & nyquist/DivergeJM readme files
Previously an outdated copy of the default readme. Updated to match the Nyquist/DivergeJM format (DivergeJM is a split 5x12 implementation of the terminus_mini layout)
* Update makefiles to rules.mk
Renamed both Makefiles to rules.mk, removed references to makefiles
* Updated rules.mk
Inadvertantly removed important code from the rules.mk in previous commit. This has been restored.
Also disabled Tap_Dance in both rules.mk files
* Moved terminus_mini to handwired
Realised that existing directory was not appropriate for the terminus_mini project, moved to handwired.
* New Frosty Flake layout for QFR TKL
Added a TKL layout for the Frosty Flake with a navigation cluster on LOWER under the left hand and a similarly functioning MOUSE layer that includes mouse navigation functionality.
* README fix & keymap update for 3 keyboards
Fixed the markdown for the handwired/terminus_mini:default, Nyqyist:DivergeJM & frosty_flake:QFR_JM.
Added TAPPING_TERM = 150 to config.h for all keyboards
Switched LT(LOWER) and LAlt on the mod row for ortholinear boards.
* Update readme for QFR_JM to include make instructions
* Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware"
This reverts commit a45f264ada09acc14fb85390407bc7ff5bb021e3, reversing
changes made to 62349c33410671a33d4041d50cf27de1d6bdd9cf.
* Revert "Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware""
This reverts commit eae54fb3be2c60dffd704261f84bab98c9e06f93.
* Added QWERTY support to the QFR_JM
Implemented variable default base layer from the Planck default keymap.
* Update README to reflect QWERTY support
* Nyquist:DivergeJM - Update RESET location
Add a reset button to both hands, accessible when halves are disconnected.
* Typo fix
* Update DivergeJM
Switched master to Left hand,
Moved Reset key to a different location
* Added macros to send R pointer & dplyr pipe
Macros added as a string of keypresses, couldn't figure out how to get SEND_STRING to work.
* Added ADJUST -> QWERTY, DVORAK, COLEMAK
Re-implemented update_tri_layer fuctionality to reset base layer for Terminus_Mini & DivergeJM Nyquist keymaps to QWERTY, DVORAK or COLEMAK via the ADJUST layer.
Updated ReadMe files accordingly.
* Fix base layout diagram for Terminus_Mini
Remove split from diagram
* Changed the R operators to SEND_STRING, rather than keypress macros
* Added Dvorak to the QFR_JM keymap
* fixed duplicate row in Nyquist keymap
* Fix readme - LAlt location on mouse layer
* Set EE_HANDS to allow either Nyquist hand to work as master.
* Update R operator strings, clean up layering for terminus_mini, QFR_JM and DivergeJM
"<-" to " <- "
"%>%" to " %>% "
Also played around with the layering, removed unnecessary TAP_TOGGLE for LOWER and shuffled FUNCTION and MOUSE momentary actions to reflect layer order.
* Update bottom alpha row to output symbols on LOWER
This row now outputs the following (z -> /) when in the LOWER layer:
<-
%>%
{
[
`
|
]
}
.
/
* Updated readme files for QFR_JM, terminus_mini & DivergeJM
QFR_JM readme reflects correct LOWER bottom row symbol output,
terminus_mini & DivergeJM reflect correct command line make instructions.
* Add media keys to QFR_JM LOWER - Replicate QFR default functionality
* Fix issue with Mouse layering
Stuck on mouse layer because the wrong macro was assigned to the 'exit layer' key. Reassigned that key.
* Changed " <- " to "<- " for QFR_JM, terminus_mini & DivergeJM
* Add "KC_MAKE" to userspace example
* QMK DFU bootloader generation (#2009)
* adds :bootloader target
* update planck and preonic revisions
* remove references to .h files for planck
* update preonic keymap
* only add keyboard.h files that exist
* add production target
* hook things up with the new lufa variables
* update rules for planck/preonic
* back backlight key turn of status led when pressed
* add manufacturer/product strings to bootloader
* fix push script
* Added support for let's split kailh socket version (#2010)
* Added support for socket version of the let's split
* renamed files
* socket-version-works
* fix up lets_split keymaps
* fix up lets_split keymaps
* shrink preonic by a bit
* fix lets_split keyboards
* update travis script
* update travis script
* update version silencing
* - Fixed DK60 version in config.h
* - Updated dk60 readme with new QMK rules
* - Fixed wording in readme
* Added dbroqua layout for DZ60
I've also updated dz60.h to add "true HHKD" keymap definition (6U
spacebar).
With the default HHKB definition r_alt was not mapped and when I pressed
r_menu it was r_alt.
Regards
* Updated dbroqua layout for HHKB keyboard
Added default configuration and alternate (swap gui/alt keys).
Save user choice in keyboard memory (like plank, thanks for this
feature!).
* adds :bootloader target
* update planck and preonic revisions
* remove references to .h files for planck
* update preonic keymap
* only add keyboard.h files that exist
* add production target
* hook things up with the new lufa variables
* update rules for planck/preonic
* back backlight key turn of status led when pressed
* add manufacturer/product strings to bootloader
* First commit of the Terminus_Mini firmware and the DivergeJM version of the Nyquist firmware
* Fix terminus_mini & nyquist/DivergeJM readme files
Previously an outdated copy of the default readme. Updated to match the Nyquist/DivergeJM format (DivergeJM is a split 5x12 implementation of the terminus_mini layout)
* Update makefiles to rules.mk
Renamed both Makefiles to rules.mk, removed references to makefiles
* Updated rules.mk
Inadvertantly removed important code from the rules.mk in previous commit. This has been restored.
Also disabled Tap_Dance in both rules.mk files
* Moved terminus_mini to handwired
Realised that existing directory was not appropriate for the terminus_mini project, moved to handwired.
* New Frosty Flake layout for QFR TKL
Added a TKL layout for the Frosty Flake with a navigation cluster on LOWER under the left hand and a similarly functioning MOUSE layer that includes mouse navigation functionality.
* README fix & keymap update for 3 keyboards
Fixed the markdown for the handwired/terminus_mini:default, Nyqyist:DivergeJM & frosty_flake:QFR_JM.
Added TAPPING_TERM = 150 to config.h for all keyboards
Switched LT(LOWER) and LAlt on the mod row for ortholinear boards.
* Update readme for QFR_JM to include make instructions
* Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware"
This reverts commit a45f264ada09acc14fb85390407bc7ff5bb021e3, reversing
changes made to 62349c33410671a33d4041d50cf27de1d6bdd9cf.
* Revert "Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware""
This reverts commit eae54fb3be2c60dffd704261f84bab98c9e06f93.
* Added QWERTY support to the QFR_JM
Implemented variable default base layer from the Planck default keymap.
* Update README to reflect QWERTY support
* Nyquist:DivergeJM - Update RESET location
Add a reset button to both hands, accessible when halves are disconnected.
* Typo fix
* Update DivergeJM
Switched master to Left hand,
Moved Reset key to a different location
* Added macros to send R pointer & dplyr pipe
Macros added as a string of keypresses, couldn't figure out how to get SEND_STRING to work.
* Added ADJUST -> QWERTY, DVORAK, COLEMAK
Re-implemented update_tri_layer fuctionality to reset base layer for Terminus_Mini & DivergeJM Nyquist keymaps to QWERTY, DVORAK or COLEMAK via the ADJUST layer.
Updated ReadMe files accordingly.
* Fix base layout diagram for Terminus_Mini
Remove split from diagram
* Changed the R operators to SEND_STRING, rather than keypress macros
* Added Dvorak to the QFR_JM keymap
* fixed duplicate row in Nyquist keymap
* Fix readme - LAlt location on mouse layer
* Set EE_HANDS to allow either Nyquist hand to work as master.
* Update R operator strings, clean up layering for terminus_mini, QFR_JM and DivergeJM
"<-" to " <- "
"%>%" to " %>% "
Also played around with the layering, removed unnecessary TAP_TOGGLE for LOWER and shuffled FUNCTION and MOUSE momentary actions to reflect layer order.
* Update bottom alpha row to output symbols on LOWER
This row now outputs the following (z -> /) when in the LOWER layer:
<-
%>%
{
[
`
|
]
}
.
/
* Updated readme files for QFR_JM, terminus_mini & DivergeJM
QFR_JM readme reflects correct LOWER bottom row symbol output,
terminus_mini & DivergeJM reflect correct command line make instructions.
* Add media keys to QFR_JM LOWER - Replicate QFR default functionality
* Fix issue with Mouse layering
Stuck on mouse layer because the wrong macro was assigned to the 'exit layer' key. Reassigned that key.
* Changed " <- " to "<- " for QFR_JM, terminus_mini & DivergeJM
* importing 42 key dvorak layout
* added comment for build instructions
* adding atreus dvorak 42 key layout
* added readme
* add readme
* build instructions
* additional MEH shortcuts
* added shifted symbols on symbols layer
* working extra symbols on COMBINED layer
* bring atreus layout inline with the ergodox one
* add necessary macros
* working ls macro
* added more shell macros
* added screen rename / screen number macros
* add ctrl-a key in shell-nav to use screen more easily
* added shell screen layer
* assign screen switching macros to screen layer
* define all screen switching macros
* more screen-related shortcuts added on shell screen layer
* change shell nav bottom right row to match base layer (backspace / delete)
* remove some mappings on SHELL_NAV layer as they are now in the screen layer
* added more screen macros
* changes to COMBINED layer (pipe on the right) and modified shell nav
* moved pipe/backslash to then right
* documented SHELL_SCREEN layer
* put backspace/delete on SHELL_NAV layer
* More keymap fixes. F-row on bottom layer wasn't fully setup, also switched raise/lower keys to use tap-toggle.
* Added PrScr, put Tab back on top layer.
* Fixed build breakage with default keymap (unneeded rgblight.h include)
* Add yuuki keymap
Documentation is still a TODO and the keymap may not be final
* GRV on colon
* add KC_GRV to FN ESC
* more RGB modes
* Update README.md
Add image of layout and fix typo
* switch from jpg to png
For some reason the JPG had red outlines around the keys.
* remove whitespace
* add instruction to reset keyboard before flashing
* gh60 stytle layout
* moved the GH60 style layout to new folder
* add HOME and END
* Add heading
* moved ayanami to other branch
* restructure converters
each converter is its own keyboard and different hardware variants are different subprojects.
remove (seemingly) old method of loading layouts from main Makefile
* call led_set_kb() from overridden led_set()
* put converter back into one folder
* revert some structure changes to bring in line with #1784.
Also attempt to get the BLE thing more properly integrated.
Also also fix led_set() to call led_set_kb().
* Add woodpad
* Cleanup
* Remove misc layouts for woodpad
* Move woodpad to handwired
* Updated RGB Underglow info
* Cleanup macros
* Tweaked RGB lighting stuff
* Start to merge orthodox/ergodox keymaps (persistant layers)
* Add woodpad
* Add forced NKRO
* Added default layer (qwerty/colemak/dvorak) detection to RGB Underglow
* Updated macros and added workman keymaps
* Fixed RGB lighting for Workman layout
* Add leader keys
* Remove force NKRO
* Add Viterbi one handed layout and minor tweaks to others
* Finishing up Viterbi keyboard layout, and NKRO tweaks to other layouts
* Made "make" keystroke universal
* Clean up and updates of drashna keymaps
* Add workman layer to planck
* Update to keymaps
* Fix makefile toggle code in ez keymap
Finish adding RGB code to orthodox
* Updated RGB Underglow layer indication code due to discovery of the layer_state_set_kb function
* Remove unnecessary planck layout
* Fixed Workman song
* update make command and added lit reset
* Fixed formatting to fall in line with official standards
* Minor tweaks
* Removed Leader Keys from Ergodox EZ Keymap
Added KC_RESET that resets board and sets underglow to red
* Tweak reset code
* Cleanup
* Remove misc layouts for woodpad
* Move woodpad to handwired
* Updated RGB Underglow info
* Cleanup macros
* Tweaked RGB lighting stuff
* Start to merge orthodox/ergodox keymaps (persistant layers)
* Add forced NKRO
* Added default layer (qwerty/colemak/dvorak) detection to RGB Underglow
* Updated macros and added workman keymaps
* Fixed RGB lighting for Workman layout
* Add leader keys
* Remove force NKRO
* Add Viterbi one handed layout and minor tweaks to others
* Finishing up Viterbi keyboard layout, and NKRO tweaks to other layouts
* Made "make" keystroke universal
* Clean up and updates of drashna keymaps
* Add workman layer to planck
* Update to keymaps
* Fix makefile toggle code in ez keymap
Finish adding RGB code to orthodox
* Updated RGB Underglow layer indication code due to discovery of the layer_state_set_kb function
* Remove unnecessary planck layout
* Fixed Workman song
* update make command and added lit reset
* Fixed formatting to fall in line with official standards
* Minor tweaks
* Removed Leader Keys from Ergodox EZ Keymap
Added KC_RESET that resets board and sets underglow to red
* Tweak reset code
* Fix rebasing issues
* remove head files
* Fix "macro" issue
* Rename ez keymaps for userspace
* Revert "Rename ez keymaps for userspace"
This reverts commit c25425911852e41711a5f0273b5741adb16e5bd4.
* Renamed Ergodox EZ layouts so that all of my personal layouts are on the same name, in prep for using userspaces
* Fix ergodox code
* Remove "drashna-ez" keymap as it's no longer needed
* Migrate majority of code to Userspace
* Add woodpad
* Cleanup
* Remove misc layouts for woodpad
* Move woodpad to handwired
* Updated RGB Underglow info
* Cleanup macros
* Tweaked RGB lighting stuff
* Start to merge orthodox/ergodox keymaps (persistant layers)
* Add woodpad
* Add forced NKRO
* Added default layer (qwerty/colemak/dvorak) detection to RGB Underglow
* Updated macros and added workman keymaps
* Fixed RGB lighting for Workman layout
* Add leader keys
* Remove force NKRO
* Add Viterbi one handed layout and minor tweaks to others
* Finishing up Viterbi keyboard layout, and NKRO tweaks to other layouts
* Made "make" keystroke universal
* Clean up and updates of drashna keymaps
* Add workman layer to planck
* Update to keymaps
* Fix makefile toggle code in ez keymap
Finish adding RGB code to orthodox
* Updated RGB Underglow layer indication code due to discovery of the layer_state_set_kb function
* Remove unnecessary planck layout
* Fixed Workman song
* update make command and added lit reset
* Fixed formatting to fall in line with official standards
* Minor tweaks
* Removed Leader Keys from Ergodox EZ Keymap
Added KC_RESET that resets board and sets underglow to red
* Tweak reset code
* Cleanup
* Remove misc layouts for woodpad
* Move woodpad to handwired
* Updated RGB Underglow info
* Cleanup macros
* Tweaked RGB lighting stuff
* Start to merge orthodox/ergodox keymaps (persistant layers)
* Add forced NKRO
* Added default layer (qwerty/colemak/dvorak) detection to RGB Underglow
* Updated macros and added workman keymaps
* Fixed RGB lighting for Workman layout
* Add leader keys
* Remove force NKRO
* Add Viterbi one handed layout and minor tweaks to others
* Finishing up Viterbi keyboard layout, and NKRO tweaks to other layouts
* Made "make" keystroke universal
* Clean up and updates of drashna keymaps
* Add workman layer to planck
* Update to keymaps
* Fix makefile toggle code in ez keymap
Finish adding RGB code to orthodox
* Updated RGB Underglow layer indication code due to discovery of the layer_state_set_kb function
* Remove unnecessary planck layout
* Fixed Workman song
* update make command and added lit reset
* Fixed formatting to fall in line with official standards
* Minor tweaks
* Removed Leader Keys from Ergodox EZ Keymap
Added KC_RESET that resets board and sets underglow to red
* Tweak reset code
* Fix rebasing issues
* remove head files
* Fix "macro" issue
* Rename ez keymaps for userspace
* Revert "Rename ez keymaps for userspace"
This reverts commit c25425911852e41711a5f0273b5741adb16e5bd4.
* Renamed Ergodox EZ layouts so that all of my personal layouts are on the same name, in prep for using userspaces
* Fix ergodox code
* Remove "drashna-ez" keymap as it's no longer needed
* Set up tap dance for layers on the lower button.
* Refactored code to share in the users directory between my two keyboard layouts.
* Small keyboard layout change.
* Updated documentation on oneshot usage in macros/tap dance.
* importing 42 key dvorak layout
* added comment for build instructions
* adding atreus dvorak 42 key layout
* added readme
* add readme
* build instructions
* additional MEH shortcuts
* added shifted symbols on symbols layer
* working extra symbols on COMBINED layer
* bring atreus layout inline with the ergodox one
* add necessary macros
* working ls macro
* added more shell macros
* added screen rename / screen number macros
* add ctrl-a key in shell-nav to use screen more easily
* added shell screen layer
* assign screen switching macros to screen layer
* define all screen switching macros
* more screen-related shortcuts added on shell screen layer
* change shell nav bottom right row to match base layer (backspace / delete)
* remove some mappings on SHELL_NAV layer as they are now in the screen layer
* added more screen macros
* Fix RGBLIGHT startup color
While it's awesome to see the layer indicating code in here (no really!), and the general rule is to not alter the default keymap/code....
The problem with the layer_state_set_kb call handling this, is that the code doesn't seem to be called at startup. So the default layer color won't ever get set on startup. It needs to be called in the init function to be properly set.
I've played with this extensively, and if you check my keymaps, that is precisely why I have the setrgb/sethsv in the init function.
* Removed typo (pipe)
* mitosis/datagrok: reduce features from rules.mk
* mitosis/datagrok: make both layer keys neighbor shift
* mitosis/datagrok: (no-op) tweak some comments
* mitosis/datagrok: set baudrate to 250k
This requires a corresponding change to the mitosis wireless firmware:
https://github.com/reversebias/mitosis/pull/10
* mitosis/datagrok: move design description from code comment to a readme
* mitosis/datagrok: new layout, new shifted keys, efficient LED code
This is experimental, but compiles and seems to work correctly.
* mitosis/datagrok: whoops, move readme.md
* mitosis/datagrok: a minor layout improvement simplifies custom-shifted code
instead of [, .] [? !], using [, ?] [. !] greatly simplifies the code
needed to perform the shifted-key switching. (And keeps , and . on the
same keys that they are under qwerty.)
also: layout improvements for symbols
* mitosis/datagrok: make my code conform to QMK style guidelines
* mitosis/datagrok: TODO note for layout table in README
* mitosis/datagrok: remove led_set_user until i figure out other changes
need to see if the corresponding changes needed in the keyboard-level code
is okay.
* mitosis/datagrok: simpler layer indicator
* mitosis/datagrok: undo change to keyboard baud; make it in my layout dir.
* mitosis/datagrok: apply same punctuation hack to qwerty layer
* mitosis/datagrok: enable qwerty layer toggle
* mitosis/datagrok: update readme
* Add satan keymap: HHKB-alike based on dbroqua's, with mouse functionality and without LED functionality
* move mouse layer to DOUBLE_HOLD, add UTIL layer for TRIPLE_HOLD
- UTIL layer
- currently has "RESET" key and nothing else.
- functionality otherwise covered by bootmagic should go here
- small bugfix: dispatch of [QTY]_HOLD should be based on range tap count
falls in, not exact count.
* Added support for Knops Mini (3x2 macropad) keyboard.
* Added better documentation, according to the QMK standards.
* Fixed typo.
* Changed names of files to comply with QMK standards.
* Ignored makefile in keymap.
* Removed makefiles and added my credentials in the copyrights.
* Add woodpad
* Cleanup
* Remove misc layouts for woodpad
* Move woodpad to handwired
* Updated RGB Underglow info
* Cleanup macros
* Fix odd merge issue
* Tweaked RGB lighting stuff
* Start to merge orthodox/ergodox keymaps (persistant layers)
* Add forced NKRO
* Added Colemak and Dvorak layers to default orthodox keymap
* Added default layer (qwerty/colemak/dvorak) detection to RGB Underglow
* Updated macros and added workman keymaps
* Fixed RGB lighting for Workman layout
* Add leader keys
* Remove force NKRO
* Add Viterbi one handed layout and minor tweaks to others
* Finishing up Viterbi keyboard layout, and NKRO tweaks to other layouts
* Made "make" keystroke universal
* Clean up and updates of drashna keymaps
* Add workman layer to planck
* Update to keymaps
* Fix accidental commit because I don't know how to git
* Fix makefile toggle code in ez keymap
Finish adding RGB code to orthodox
* missing underscore in init function declaration
* Updated RGB Underglow layer indication code due to discovery of the layer_state_set_kb function
* Remove unnecessary planck layout
* Created Kona Classic config
* Fixed KonaClassic config
* Updated README
* Updated Readme to conform to format standards
* Added ANSI and ISO layout options
* Fixed images in Readme
* Added labels to images
* Added absolute links to images in Readme
* Image link updates again
* Fixed bottom row keys in some layouts
* Fixed Grave and Tilde
* Fixed Underglow in Kona Classic configs
* Renamed KonaClassic to kona_classic
* First commit of the Terminus_Mini firmware and the DivergeJM version of the Nyquist firmware
* Fix terminus_mini & nyquist/DivergeJM readme files
Previously an outdated copy of the default readme. Updated to match the Nyquist/DivergeJM format (DivergeJM is a split 5x12 implementation of the terminus_mini layout)
* Update makefiles to rules.mk
Renamed both Makefiles to rules.mk, removed references to makefiles
* Updated rules.mk
Inadvertantly removed important code from the rules.mk in previous commit. This has been restored.
Also disabled Tap_Dance in both rules.mk files
* Moved terminus_mini to handwired
Realised that existing directory was not appropriate for the terminus_mini project, moved to handwired.
* New Frosty Flake layout for QFR TKL
Added a TKL layout for the Frosty Flake with a navigation cluster on LOWER under the left hand and a similarly functioning MOUSE layer that includes mouse navigation functionality.
* README fix & keymap update for 3 keyboards
Fixed the markdown for the handwired/terminus_mini:default, Nyqyist:DivergeJM & frosty_flake:QFR_JM.
Added TAPPING_TERM = 150 to config.h for all keyboards
Switched LT(LOWER) and LAlt on the mod row for ortholinear boards.
* Update readme for QFR_JM to include make instructions
* Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware"
This reverts commit a45f264ada09acc14fb85390407bc7ff5bb021e3, reversing
changes made to 62349c33410671a33d4041d50cf27de1d6bdd9cf.
* Revert "Revert "Merge branch 'master' of https://github.com/mogranjm/qmk_firmware""
This reverts commit eae54fb3be2c60dffd704261f84bab98c9e06f93.
* Added QWERTY support to the QFR_JM
Implemented variable default base layer from the Planck default keymap.
* Update README to reflect QWERTY support
Previously, this code was implemented in keymap.c, but I'm unaware of
someone with a different implementation of this particular hack. [If
someone has it, we can add another #ifdef in the future.]
* Added personal minivan keymap
more consistent layer setup
documentation!
slide some things around
more doc jiggling
* Small layout and documentation tweaks
Small documentation updates
dropped Makefile that for some reason was still in my branch
* found and removed extra makefile
* added bfake support as a subproject
also moved existing bmini stuff to a subproject
fixed columns
minor keymap update
making this a subproject
remove old stuff
got subproject stuff figured out
* travis was upset because a board didn't have a default keymap
* - Fixed DK60 version in config.h
* - Updated dk60 readme with new QMK rules
* - Fixed wording in readme
* Added dbroqua layout for DZ60
I've also updated dz60.h to add "true HHKD" keymap definition (6U
spacebar).
With the default HHKB definition r_alt was not mapped and when I pressed
r_menu it was r_alt.
Regards
* First commit of the Terminus_Mini firmware and the DivergeJM version of the Nyquist firmware
* Fix terminus_mini & nyquist/DivergeJM readme files
Previously an outdated copy of the default readme. Updated to match the Nyquist/DivergeJM format (DivergeJM is a split 5x12 implementation of the terminus_mini layout)
* Update makefiles to rules.mk
Renamed both Makefiles to rules.mk, removed references to makefiles
* Updated rules.mk
Inadvertantly removed important code from the rules.mk in previous commit. This has been restored.
Also disabled Tap_Dance in both rules.mk files
* Moved terminus_mini to handwired
Realised that existing directory was not appropriate for the terminus_mini project, moved to handwired.
* New Frosty Flake layout for QFR TKL
Added a TKL layout for the Frosty Flake with a navigation cluster on LOWER under the left hand and a similarly functioning MOUSE layer that includes mouse navigation functionality.
* Add existing file
* Add new keyboard layout - initial commit
* Revised readme.md
* Clarified readme.md, reorganized keymap.c, and added license text.
* Fixing last incomplete commit
* Just a little code cleanup to make things more readable.
* Add carvac_dv keymap for mitosis
* Add mouse keys
* move backspace, etc, and fix tab
* remove commented-out functions in keymap
* Fix scroll buttons and add left/right scrolling
* Make num momentary, add comments, and clean up
* fix mouse scroll acceleration
* Add tab, remove bksp, move print screen
Having tab next to control and alt makes for much easier
alt-tabbing and ctrl-tabbing.
That displaced print screen, but I had never used the non-layer
backspace on the right hand, so I moved printscreen over there.
* - Fancy default PID and option for corresponding VID.
- Information about official VID/PID.
- Correct manufacturer name.
- NKRO enabled by default.
* Resolved build error with `#ifndef FORCE_NKRO`.
* Clone Nyquist code to Iris and rename
* Set keymap and pins
* Work in progress Iris default keymap
* Add Iris rev2
* Update Iris files to new build system
* Add lewisridden keymap
* Address #1689 by using a formula to define the breathing curve and exposing defines to control the shape of the curve.
* Tweak the behavior of breathing for clueboard
* First commit of the Terminus_Mini firmware and the DivergeJM version of the Nyquist firmware
* Fix terminus_mini & nyquist/DivergeJM readme files
Previously an outdated copy of the default readme. Updated to match the Nyquist/DivergeJM format (DivergeJM is a split 5x12 implementation of the terminus_mini layout)
* Update makefiles to rules.mk
Renamed both Makefiles to rules.mk, removed references to makefiles
* Updated rules.mk
Inadvertantly removed important code from the rules.mk in previous commit. This has been restored.
Also disabled Tap_Dance in both rules.mk files
* Moved terminus_mini to handwired
Realised that existing directory was not appropriate for the terminus_mini project, moved to handwired.
* redo make args to use colons, better folder structuring system [skip ci]
* don't put spaces after statements - hard lessons in makefile development
* fix-up some other rules.mk
* give travis a chance
* reset KEYMAPS variable
* start converting keyboards to new system
* try making all with travis
* redo make args to use colons, better folder structuring system [skip ci]
* don't put spaces after statements - hard lessons in makefile development
* fix-up some other rules.mk
* give travis a chance
* reset KEYMAPS variable
* start converting keyboards to new system
* try making all with travis
* start to update readmes and keyboards
* look in keyboard directories for board.mk
* update visualizer rules
* fix up some other keyboards/keymaps
* fix arm board ld includes
* fix board rules
* fix up remaining keyboards
* reset layout variable
* reset keyboard_layouts
* fix remainging keymaps/boards
* update readmes, docs
* add note to makefile error
* update readmes
* remove planck keymap warnings
* update references and docs
* test out tarvis build stages
* don't use stages for now
* don't use stages for now
* add ymd96 base
currently not working correctly.
* Update
honestly not really sure what I've been doing but I'm just more or less brute forcing this until I can get the pcb schematic or something
* honestly just trying stuff out
* Update keymaps
Getting closer hopefully
* ymd96 works!
at least for me
* Update readme
* Update readme
* Update readme
* Adds support for multiple layouts. Adds custom keymap for "offset"
layout.
* Adds a tool to help detach the keyboard from the Linux HID driver before programming.
* Adds a tool to help detach the keyboard from the Linux HID driver before programming.
- a keyboard already in bootloader mode will now be detected
- if setting the keyboard to bootloader mode doesn't work, a hint will be printed on how to do so
- instead of failing instantly when no keyboard is found, the script will now wait up to 60 seconds (it retries every 5 seconds, up to 12 times)
neue Datei: keyboards/lets_split/keymaps/DE_simple/config.h
neue Datei: keyboards/lets_split/keymaps/DE_simple/keymap.c
neue Datei: keyboards/lets_split/keymaps/DE_simple/rules.mk
* slight modifier changes; added plover and reusing jack's default planck keymap as the basis
* space is not shift when held anymore
* added fabian layout (based on jack's default)
* changed fabian layout (based on jack's default)
* changed fabian layout (based on jack's default)
* Fix mbsurfer let's split layout RGB indicators when both lower and raise are pressed
* Update mbsurfer let's split keymap with new RGB key codes for modes
* Clean up mbsurfer keymap matrix layout
* initial clueboard_60 support
* LED lighting support
* fix the clueboard->clueboard_66 rename
* Add layout support to clueboard_60
* Fix the 60_iso layout so it's actually iso
* add a default keymap for AEK layout
* fix clueboard_17
* Fixup the ISO layouts
* Fix the `wait_ms()/wait_us()` definitions for chibios
* Fix up the wait_ms/wait_us hack. Reduce stack size.
* Add a missing #include "wait.h"
* commit files that should have already been comitted
* Support for KBP V60 Type R 60% keyboard
Support does not include in switch or underglow lighting for Polestar Edition.
* rename v60type_r to v60_type_r
* Remove old v60type_r
* Modify readme.md to adhere with QMK readme formatting.
tearing it down so that it can be rebuilt
fiddling with audio
big default config overhaul
apparently startup sounds work without the override now
readme!
readme fixes
readme tweaking
* Add yuuki keymap
Documentation is still a TODO and the keymap may not be final
* GRV on colon
* add KC_GRV to FN ESC
* hhkb ish
* hhkbish 2
* HHKBish and documentation
* Fix Markdown warnings
* typo
* phreed keymap added
This keymap moves many pinky keys to the center
* set to do what I want but LT() does not return to previous layer
* get overlays working
* get overlays working
* fix the readme
* fix the readme
* swapped the shift
* swapped the shift
* propagate mods
* clear special char on readme
* Implement sticky modifiers
* Change underglow based on sticky mod status
* Set RGB lights based on which mods are stickied
* Add controls for dimming RGB LEDs
* Only update RGB lights if modifiers have changed
* Use all LEDs to show modifier state
* Create default keymap for Viterbi
* Duplicate default layout as basis of my own
* Basic Colemak layer, just to practice flashing
* Add reset button so that we don't have to short out the reset button on the board to flash it.
* Symbols layer
* Navigation layer, and remove unused keys. Now usable, nice.
* Correct backspace for UK QWERTY mapping
* Small clarification in XD75RE readme instructions
* Use UK pipe so that I can type a pipe on a UK keyboard
* adding new layout for the planck that helps when coming from the pok3r
* Fixing the function layer
* Update readme.md
* Update keymap.c
Making some small adjustments
* Update keymap.c
switching GUI and Esc
* Update keymap.c
* changed 'infinity' to 'ergodox_infinity' and specified to be in the top-level directory as per recent changes to directory structure of QMK_firmware git repo
* accidently removed '-' in last line of readme
* add new RGB keycodes and clean up lets split keymap
* extraneous cases
* More cleanup and added macro
* one more macro
* cleaned up my planck keymap and added macros
* Transitioned planck keymap to new formatting / audio modes based on new default
* Remove extraneous newline in song list, add keycodes missed in previous commit
* error in graphical representation of keycodes
* Merge with upstream
* Finish merge
* Add new keymap
* Change use of KEYMAP macro
* Add Readme.md
* Fix link
* Clean up comments
* Raise on leading edge of keypress
* Add HOME/END keys as upper/lower on arrow-up/down
* Reduce .hex file size by turning off unneeded options
* Put digit keypad onto left hand upon RAISE; this will sometimes be preferable to double-hits of right hand
* Latest super latest version merge
* cbbrowne keymap for XD75re
* starting notes on XD75re keymap plans
* First draft of bottom row of QWERTY
* Switch my special bottom line over to QCENT
* Dunno
* Filling in wanted keys, bit by bit...
* Add copyright, extra macro
* Clean up comments, remove some experimental code I didn't like
* TODO plans for xd75re
* clean up keyboard layout
* QCENT2 is my new experiment for the main keyboard...
* Add a few more main layer keys, and modify LOWER to shift things outwards to conform with main layer
* Clean up RAISE layer to conform with main layer, remove QCENT layer as QCENT2 is the new thing
* More xd75 changes, now that I actually have it in hand
* shift keymap around, as original attempt was a bit too aggressive in keeping to the edges
* more revs to XD75
* Dropping parts of the centre keypad in favor of Keys I Really Need
* Improve documentation to conform with how builds are done now
* Improve documentation to conform with how builds are done now
* Add cbbrowne rules file as alternative to having the rules in Makefile
* Makefile not needed anymore for individual keymap
* Remove all Makefiles from the keyboards directory.
* update keymaps added in the last 8 days
* Ignore keyboard/keymap makefiles
* update hand_wire to reflect our new Makefile-less reality
* Update the make guide to reflect the new reality
* move planck keymap options to rules.mk
* update planck keymaps 4real
* trigger travis
* add back build_keyboard.mk
* restore changes to build_keyboard
* Allow the knight animation to be restricted to a portion of the LED strip
* Add keys for jumping directly to particular animation modes
* Remove orphaned break statements
* Tweak the `RGB_MODE` buttons so they cycle through the same mode.
* small indentation fix
* Add a new revision of the clueboard with 18 underlight LEDs
* Allow the knight animation to be restricted to a portion of the LED strip
* Add keys for jumping directly to particular animation modes
* Remove orphaned break statements
* Tweak the `RGB_MODE` buttons so they cycle through the same mode.
* small indentation fix
* copied mjt keymaps from archive
* All mjt boards now compile
* fixed jd45-mjt breathing
* Updates to fix SpaceFN but not tested yet.
* Still missing either spacebar or an adjacent keypress.
* Debugging rigged up for use with hid_listen.
* Reverted the default keymap to use tap_layer_key rather than custom. Moved custom approach to keymap_debug.c
* Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function.
* Cleaned up JD45 keymap that uses tapkey.
* Redid minivan keymap with numsym rather than raise/lower.
Untested.
* Created my MJT keymap for HHKB
Enabled dynamic macros and moved
somoe of the shortcuts around.
* Minor keymap fixes to make them compile without errors.
* Added home/end to right arrow cluster on DYN layer.
* Added more keys to fn and dyn layers.
* It wasn't using my custom layer last time somehow...? Now it will.
* Compiled and installed at end of day on 8/23
* Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback.
* Fixed volume controls... were reversed and disabled.
* Added F13-F15 back to fkeys layer in Minivan
* Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan.
* Removed DYN layer.
* Fixed diagram in planck numsym.
* Cleanup for pull request.
* Roadkit flip phone warning.
* Replaced PLAY_NOTES_ARRAY to PLAY_SONG
* reset the submodules
* checked out specific commits for submodules
* Removed debugging from JD45 shared config.h
* Moved custom rules.mk to apropriate keymap
Reset the shared rules.mk file.
* Trailing return issue in rules.mk
Gotta make for a smooth pull request :-)
* Mitosis music troubleshooting
Also updated the song playing function.
Does not work currently.
* Fixed mitosis audio
* Put mitosis/rules.mk back to QMK master
* copied mjt keymaps from archive
* All mjt boards now compile
* fixed jd45-mjt breathing
* Updates to fix SpaceFN but not tested yet.
* Still missing either spacebar or an adjacent keypress.
* Debugging rigged up for use with hid_listen.
* Reverted the default keymap to use tap_layer_key rather than custom. Moved custom approach to keymap_debug.c
* Fixed the lower-left side of the keymap, which needed more spacers due to the matrix being directly put into the array rather than using the keymap function.
* Cleaned up JD45 keymap that uses tapkey.
* Redid minivan keymap with numsym rather than raise/lower.
Untested.
* Created my MJT keymap for HHKB
Enabled dynamic macros and moved
somoe of the shortcuts around.
* Minor keymap fixes to make them compile without errors.
* Added home/end to right arrow cluster on DYN layer.
* Added more keys to fn and dyn layers.
* It wasn't using my custom layer last time somehow...? Now it will.
* Compiled and installed at end of day on 8/23
* Moved macros to FKEY layer because Adjust was too hard to get into and out of without some sort of feedback.
* Fixed volume controls... were reversed and disabled.
* Added F13-F15 back to fkeys layer in Minivan
* Created new Planck Keymap that uses the NumSym and FKeys layer approach like the Minivan.
* Removed DYN layer.
* Fixed diagram in planck numsym.
* Cleanup for pull request.
* Roadkit flip phone warning.
* Replaced PLAY_NOTES_ARRAY to PLAY_SONG
* reset the submodules
* checked out specific commits for submodules
* Removed debugging from JD45 shared config.h
* Moved custom rules.mk to apropriate keymap
Reset the shared rules.mk file.
* Trailing return issue in rules.mk
Gotta make for a smooth pull request :-)
* include variables and .h files as pp directives
* start layout compilation
* split ergodoxes up
* don't compile all layouts for everything
* might seg fault
* reset layouts variable
* actually reset layouts
* include rules.mk instead
* remove includes from rules.mk
* update variable setting
* load visualizer from path
* adds some more examples
* adds more layouts
* more boards added
* more boards added
* adds documentation for layouts
* use lowercase names for LAYOUT_
* add layout.json files for each layout
* add community folder, default keymaps for layouts
* touch-up default layouts
* touch-up layouts, some keyboard rules.mk
* update documentation for layouts
* fix up serial/i2c switches
Turns out that 3c and 3d are not reversed when splitting the right
shift in the way that the Mark I layout does. Reversing it here, rather
than in the generic satan.h to avoid breaking the other layouts.
Fix and issue with the original Sentraq S60-X not being compatible with 'default'. If 'default' shouldn't be changed, perhaps I can create an 'original' revision.
