qmk_firmware/keyboards/exclusive/e6v2/bmc/rules.mk
MechMerlin 04684a94ef [Keyboard] E6V2 Bootmapper Client QMK port (#5495)
* initial commit of e6v2 bmc files

* update readme with bmc template and reset key location

* fix up the switch matrix

* add usbconfig.h file

* add i2c files

* cleanup config.h

* cleanup rules.mk and remove non atmega32a architecture code

* add an appropriate keymap for testing

* update readme with warning not to flash this hex file onto atmega32u4 e6v2

* get rgb lights working

* add QMK Configurator support for 60_ansi layout

* add hhkb support layout

* add additional layouts such as tsangan and all and included QMK Configurator support for them

* add bootmagic lite, and have it be set to Esc or the key located at k50

* update readme

* fixup spacing for LAYOUT_all electrical matrix

* add some pragma once magic

* use i2c_master instead of custom i2c.c

* remove the custom i2c.c

* restore a more valid default keymap

* add eep_rst to keymap
2019-03-27 22:12:17 -07:00

91 lines
3.4 KiB
Makefile

# MCU name
#MCU = at90usb1286
MCU = atmega32a
PROTOCOL = VUSB
NO_UART = yes
NO_SUSPEND_POWER_DOWN = yes
# Processor frequency.
# This will define a symbol, F_CPU, in all source code files equal to the
# processor frequency in Hz. You can then use this symbol in your source code to
# calculate timings. Do NOT tack on a 'UL' at the end, this will be done
# automatically to create a 32-bit value in your source code.
#
# This will be an integer division of F_USB below, as it is sourced by
# F_USB after it has run through any CPU prescalers. Note that this value
# does not *change* the processor frequency - it should merely be updated to
# reflect the processor speed set externally so that the code can use accurate
# software delays.
F_CPU = 12000000
#
# LUFA specific
#
# Target architecture (see library "Board Types" documentation).
# ARCH = AVR8
# Input clock frequency.
# This will define a symbol, F_USB, in all source code files equal to the
# input clock frequency (before any prescaling is performed) in Hz. This value may
# differ from F_CPU if prescaling is used on the latter, and is required as the
# raw input clock is fed directly to the PLL sections of the AVR for high speed
# clock generation for the USB and other AVR subsections. Do NOT tack on a 'UL'
# at the end, this will be done automatically to create a 32-bit value in your
# source code.
#
# If no clock division is performed on the input clock inside the AVR (via the
# CPU clock adjust registers or the clock division fuses), this will be equal to F_CPU.
# F_USB = $(F_CPU)
# Interrupt driven control endpoint task(+60)
OPT_DEFS = -DDEBUG_LEVEL=0
# Bootloader selection
# Teensy halfkay
# Pro Micro caterina
# Atmel DFU atmel-dfu
# LUFA DFU lufa-dfu
# QMK DFU qmk-dfu
# atmega32a bootloadHID
BOOTLOADER = bootloadHID
# If you don't know the bootloader type, then you can specify the
# Boot Section Size in *bytes* by uncommenting out the OPT_DEFS line
# Teensy halfKay 512
# Teensy++ halfKay 1024
# Atmel DFU loader 4096
# LUFA bootloader 4096
# USBaspLoader 2048
# OPT_DEFS += -DBOOTLOADER_SIZE=4096
# Build Options
# change yes to no to disable
#
BOOTMAGIC_ENABLE = lite # Virtual DIP switch configuration(+1000)
MOUSEKEY_ENABLE = yes # Mouse keys(+4700)
EXTRAKEY_ENABLE = yes # Audio control and System control(+450)
CONSOLE_ENABLE = yes # Console for debug(+400)
COMMAND_ENABLE = yes # Commands for debug and configuration
# Do not enable SLEEP_LED_ENABLE. it uses the same timer as BACKLIGHT_ENABLE
SLEEP_LED_ENABLE = no # Breathing sleep LED during USB suspend
# if this doesn't work, see here: https://github.com/tmk/tmk_keyboard/wiki/FAQ#nkro-doesnt-work
NKRO_ENABLE = no # USB Nkey Rollover
BACKLIGHT_ENABLE = no # Enable keyboard backlight functionality on B7 by default
RGBLIGHT_CUSTOM_DRIVER = yes
RGBLIGHT_ENABLE = yes # Enable keyboard RGB underglow
MIDI_ENABLE = no # MIDI support (+2400 to 4200, depending on config)
UNICODE_ENABLE = no # Unicode
BLUETOOTH_ENABLE = no # Enable Bluetooth with the Adafruit EZ-Key HID
AUDIO_ENABLE = no # Audio output on port C6
FAUXCLICKY_ENABLE = no # Use buzzer to emulate clicky switches
HD44780_ENABLE = no # Enable support for HD44780 based LCDs (+400)
SRC += i2c_master.c
PROGRAM_CMD = ./util/atmega32a_program.py $(TARGET).hex